Tool Auction & Tool Making

Another busy weekend.
Yesterday I got up early and went to Ledbury Tool and Timber Auction with a pocket full of cash (and an uneasy wife left at home). In the end I didn't buy much just 4 large pieces of very twisted Apple, quite thick though so it should be alright for turning (probably as tough as old boots). There was a few things I should have bid higher on but you always think that on the drive home!
Today has been productive, as well as tackling the weeds at the allotment I've started to have a bit of a tidy up in the shed and I've come to the conclusion that I need to build an extension before I build my big extension. This is because I have nowhere to store any timber, but more on that in another post.
I also started to use my High Speed Steel (HSS) that I order from china (and some from Yandles) to make some more tools.
One I made using a square section of steel, ground so it forms a point. Before I could grind it I made a simple jig (in the picture above) to make sure it always went on the grinder the same way.
The other was made using round HHS bar and is basically a spindle gouge without the flute (called a "form tool" or somethimes a "cove tool" I think). I made beech handle for them both and although not identical handles they're starting to look like a set! I've got quite a few more bits of HSS so I'll be making some more woodturning tools over the next few months. anyone got any good ideas on what I can make?

Tulipwood platter

After all my experimenting last week I thought I'd just turn something a little more traditional this week. I brought a nice big plank of "tulipwood" (sounds so much nicer than poplar) as I know it's quite soft and would be good for me to practice on.
It's quite easy to turn although it does have a habit of tearing the grain if your tools aren't really sharp, the whole piece has a greenish tinge to it (my wife thought I'd added it) but I think its a good low cost wood to practice my skills on and make some quite nice pieces with in the process.
I finished the platter with a few coats of walnut oil but it will have a few more before I find it a new home.
You here so many people tell you poplar its good for nothing I'd love to hear what other people use it for as I think its quite an attractive wood.

Spirit Stains And Liming Wax

Although my wood turning classes have finished for this term I couldn't help but email Chris (my tutor) a question or two the other day, I thought he might be missing my thousand questions a lesson. He emailed back that he'd rather come and show me than write it down, so on Tuesday night he came over. This caused a bit of confusion with me as I thought he said for me to go to his and I was over half way there when my wife phoned to tell me my mistake!

We had a good few hours for Chris to show me new techniques involving texturing, painting then liming to give different layers of colour. Using the arbotech and a metal cutting disc in the grinder to give texture and interest. He was quite annoyed at himself when he forgot the blow pipes to show me with spirit stain, but I think we still created an interesting piece. I didn't mind not using the blow pipes as he'd already gone out of his way to teach me all these things, so I was surprised when he phone me up the next night to say we'd have a another crack at it to cover all the techniques. this time though not on oak (as it was too hard for the texturing) so to bring something else to try it on.

I brought round some beech I had left over and we set about making something different, still doing a bit of texturing and liming (the liming was difficult to get right) but working more with the spirit stains on an area that we roughly textured. We used the blow pipes this time and it gives a more airbrushed effect.

Again I know these pieces aren't to every ones taste (Gorges!) but I like them and had a really enjoyable couple of evenings making them in good company. I think I'm very lucky to be friends with someone who's such a good tutor.

Thanks again Chris.

Occupational Hazard

Don't worry I've still got all my fingers!

It's just I smiled inward to myself on Sunday night when my wife said the washing machine had stopped working. She'd been on the Internet to look at the error message and it had told her it was a problem with the pump. Without even look up I said it was a nail. Probably a panel pin.

This is not the first time I have broken our washing machine. Nor would it be the only washing machine I've ever broken. Nor, will it be the last washing machine I'll probably break.

I'd call this an occupational hazard. I check my pockets on a Friday night when I put my trousers in the washing basket, but sometimes one will escape me. Most of the time I'm lucky and I'll find this little Houdini nail the next time I put on my clean work trousers, not this time though.

After about half an hour of slowly draining down the washing machine to get to the pump I managed to find the offending culprit - a 35mm oval nail, sheradised so at least it wouldn't go rusty.

Luckily for me the motor just stopped and didn't burn out, otherwise I probably wouldn't be so jovial about the whole thing! maybe I should try and use my nail gun more - strips of nails are much easier to find!

Reclaimed Pine Bowl

A few months ago when taking down the extension on the Park Keepers cottage I sawed through some big old pine purlins. As I sawed I was greeted with the most amazing pine smell and the grain looked beautiful. I put both 4m lumps of timber to one side not quite sure what I'd do with them.
Knocking off from work on Friday night I decided to saw a bit off one and see what I could make from it over the weekend. I pulled out the nails and cut a blank to have a play with.
Considering it's softwood it didn't cut that easily, with the grain tearing if my bowl gouge wasn't sharp enough. I decided to hide nothing on the timber, leaving all the nail holes and any of the white paint that would stay on. I did treat it for wood worm though.
I had a small incident when turning the back away and got a little bit too confident with the lathe running too fast. They say sometimes something happens so fast you don't know what hit you - I certainly knew what hit me square on the nose! I'll keep my face mask on till the end next time - live and learn!

I finished the bowl with finishing oil and then a coat of wax. It's not perfect but I like the feel of the finished piece.

I've got plenty of this wood to play with so I might try and make a few more that I could maybe sell, although I don't know if people would buy a pine bowl - even if the piece of pine is over 200 years old.

Something A Little Different..

At my last woodturning lesson on Thursday I was challenged by Chris to do something that I don't normally do. "Don't think square and don't think centred".

Easier said than done with my mind! I went a completely different route cutting a piece of beech, leaving the bark on then having a play on the lathe. I even got out the acrylic paints and the blow torch. I know their not to everyone's taste but it was interesting making them and quite addictive once I got going. It's the first time I've used any paints for pleasure in about 15 years! And a blow torch is always good fun to use, although I'm extra careful with all the shavings in my workshop.

I finished the backs off by leaving a tooled edge with my new Arbotech type grinder disc, which leaves a surprisingly clean finish, and fixing a small mirror hook to mount it with. Like I said I don't think these are every one's cup of tea (especially people who read this blog) but it's interesting to try out new techniques and styles.

I've also made a couple of work holding devices for the lath, both to help finish off work and remove evidence of how the wood was held on the lathe. The first is a floor polishing mop trimmed up and mounted to some MDF. This will allow me to press the piece being worked into backing and turn away the waste without damaging the inside, idea for platters and shallow bowls.

The second is for the same purpose but different shaped pieces, This is just MDF glued, clamped up and then turned down to the right shape. With the addition of a sponge between the MDF and the bowl it should work great holding the piece firm.

Anyone else make up bits and bobs like this for work holding on the lathe?

Structural Work On Roof Done!

I managed to work through the list from the structural engineer over the last few days and tick off every item from his list.
The first was to remove a section of the wall plate as the cantilevered section was rotten (the bit sticking out past the wall). This wasn't as awkward as I thought it might be, just a few 6 inch cut nails to contend with. I half lapped the new section of wall plate on, which I planed down to size as it wasn't standard, and added the strap across the top to meet the requirements the engineer had set.
This picture shows quite well why I think the roof should have been replaced- the rafters are cut on to the wrong side of the wall plate creating pressures and forces in the wrong place so its pushing out not down. I know the purlins reduces the load but I just don't like to see work left thats not right!
The next step was to splice the barge board on the end where it had gone rotten, as well as add a new cocking fillet.
I then had to add 450mm new ends to the rafters which had the worst levels of decay.
The worst job was to then chisel a section of wall plate around 4m long and add a ply facing. This was to straighten it up and provide a fixing for the gutting. This job did my chisels no favours as it was full of nails.
I also added a ply soffit to both ends and fitted the a complete new gable ladder with barge board on the far side (not an easy job on your own!).
When I'd finished I couldn't help but add a fineal to both ends just to finish it off (I wont get paid for that bit but I don't care!).

Adding a Purlin to a Roof

We're still waiting for decisions to be made about the roof at Summerfield park, but I did get permission to undertake all structural works detailed by the structural engineer.

This involves things like splicing the wall plate, repairing rafter ends and changing the gable ladder on one end (the whole roof should really be replaced but I've been shot down on that due to the councils tight budget so I'll just do as I'm told).

I did have an argument with the structural engineer when he came as he originally said that a prop in the roof was doing nothing (it was under so much tension you could play a tune on it)- but to leave it in just in case (this way he wasn't going against his original survey. I wasn't really very happy with this answer, so I got him back out to look again, he then agreed with me that something should be done. I suggested a high level purlin should be added, he just needed to tell me the size.

In the end it had to be 250mm x 100mm by just over 5m long and to be C24 strength. It took ages to find someone who stocked a timber this size and strength (most suppliers stock up to 4.8m and normally only C16 strength), still it turned up yesterday so today I could have a bit of extra help to get it into the roof.

I wont say how it got up there for many reasons but it involved 5 men and quite a bit of grunting. Once it was in the loft space I let the other guys go to another job, just leaving just another chippy and myself to fit it. A little brick work making a recess in the gable wall to take it, then packing it up with slate and using mortar to fix it in. I think it was at the limit of what we could lift between us but we were both really pleased when we could take the old prop out and have the rafters sit on the new purlin.

I think I'm doing the rest of the repairs on my own, should keep me out of trouble!

First Try At A Hollow Form

At wood turning on Thursday night Chris brought in some different tools for me to try, all to do with hollowing as I've not tried this yet.

I tried them out on some green Alder (wet wood is always good fun to turn) and after a few test pieces to get the feel of the tools I made this little wooden vase/pot. It only took about 30 minutes to make but I'm sure it will crack as it dries, although the walls are all about the same thickness. I might leave it in oil and then sand it up in a few weeks if it survives!

I always enjoy trying out new tools but its made so much better with instruction! I think I'll probably sign on for my 7th term of wood turning classes but I could do with a good (difficult) project to keep me asking questions and learning, any ideas?

A Trinity Of Craftsmen

Bit of a book review here...

Last Thursday, at wood turning, my tutor Chris lent me a book entitled "A Trinity Of Craftsmen" by Freda Derrick. The dust jacket was in tatters but it looked just my sort of book.

I enjoyed reading it and for a book written in 1950 it reads really easily and quite informal for the era. The book is basically conversations and observations that Freda has had on her travels around the Cotswold's talking about the three main trades as she sees it; the mason, the Carpenter and the smith (her holy trinity). The people she meets in the book are all passionate about their trades and all long to see a future in them but worry about the lack of "Young willing lads" to pass their knowledge onto and the need for certain jobs. It concentrates on these trades in villages and rural areas and in conjunction with farming in particular (farming seeming much more important after the war than it does now).

Its weird reading it from a perspective where the writer thinks that a carpenter and blacksmith will be essential for the future of farming and in turn the country as a whole so that we can support ourselves. Comments about welding only really being for light repairs and wooden hurdles being essential for sheep farming (metal one being no good) being quite nice to read (if only I could have lived then!).

The book is split into three sections each dealing with a trade and describing some of their tools and some of their jobs (there are drawings as well). The book also talks about the new (at the time) government training centres for people coming out of the army (even a 9 month course on hurdle making). The section on the carpenter is a little light in content but still makes an interesting read, the section on the mason and smith seem to read much better with a bit more detail.

In all I really enjoyed this book and although its hardly "The Village Carpenter" (Which I think I've read about 6 times now) its a great look back at the past and good to see that even then people were worried about the disappearance of our rural crafts and the altering of village life in general. Also a nice song about a carpenter in there!

Sycamore Bowl

At the weekend I made a sycamore bowl from a blank I brought at Yandles a while back. Its the first time I've worked with this wood and it turns really nicely and takes a good finish.

As for work I've been having problems on Summerfield Park. Last Thursday night we got broken into (through the roof) and someone took about half the copper pipework that had been installed. I then spent Friday boarding it up and trying to make it secure, over the weekend they made another hole in the roof and had the rest of the copper away. This cost the firm I'm working for money and delays the project even further.

Then to top it all off my computer got a virus and I had to completely wipe and reinstall everything (not how I like spending my time!).

Still the sun was shinning today and who knows what the rest of the week will bring.

Bit of Roof Work from a few years ago

I was looking through some old photos the other day and I came across a roof that Andy and me did back in 2005/2006. This was a lovely old barn that we were there to convert and we saw it through from start to finish, in fact this was a barn i used to play in as a kid as it's only a few miles from where I grew up. Andy still works for the firm who we did this through, they were a great little firm to work for.
When we started this roof I was a bit more daunted than Andy (or he didn't let it show) as the one side had a massive run where three full lengths of timber had to be used for the rafters, being birds mouthed onto purlins and the angle of the one side of the roof made things even more complicated. As well as this when we got there we had to brush the snow off the scaffold! I remember being dogged by bad weather and hiding under blue sheets out of the rain, the yard in front of the barn had a puddle that was over a foot deep! When we got the rafters on it was a great feeling, made slightly worse by the fact that we had to then felt, batten and tile the whole thing.
The tiling started in the new year and here I learnt a valuable lesson about work. We were tiling in the snow, wrapped up against the elements, and I started to feel bad, so bad in fact I had to go home early and take the next day off (My first ever day off ill). I then felt slightly better and went back to work, I made myself so much worse because I wasn't ready to go back - in the end I nearly gave myself pneumonia and had to have x-rays with fluid on the lungs! Three weeks off in total, for a self employed man this is never good.
Still I bounced back and came back in time to do the larch cladding and the work on the inside with Andy.I loved doing this barn conversion (wish I had more pictures!).
Good times

Renovating a Roof

The last few days at work I've been renovating an old roof. In the end I think it would have been easier to have taken it completely off and start again but never mind. At least we didn't have to alter the purlins by doing it this way (although some of the rafters had to be packed to catch the purlins).
On one side of the roof I replaced every rafter due to rot and woodworm whereas on the second side I just extended each one down so it will cover the future external insulation as these were all sound. Where the rafters were replaced everyone had to be cut to a different length due to the building being out of square, this made it a bit of a slower job, but its only a small roof!
I decided that although the specifications said to insulate between the rafters and on top I made it a "warm roof" and insulated only on top, this keeps the air flow between the rafters but used a more expensive insulation to meet regulations - the building inspector was happy with this solution.

The roof insulated and counter battened, ready now for felt, batten and tiling.

To the Grind Stone

Last Thursday I committed a sin.

I lent my labourer a chisel (I'm sure you can see where this is going...)

It came back lighter than it went out. Still a little time on the grinder and its as good as new (a little shorter maybe, but as good as new), this is why carpenters don't lend tools (I know he didn't mean to do it though)

At woodturning I have been grinding some HSS bar that I brought at Yandles to make some new woodturning tools. The first of these tools is a three point tool, it seems a good tool to work with (when I've borrowed Chris's) with loads of uses and good for fine detail, as well as forming beads on bowls.

The raw materials used (Beech blank is a bit big but its all I had)

I made the handle out of beech and fitted a brass ferrule onto it. The steel took a long time to grind but it was quite easy to do as I used a triangle piece of MDF as a jig, this was to make sure all three sides were even so they met in the middle.

I'm quite please with it and I know I'll enjoy using it.

Anyone else been making their own tools lately?